User Mode Linux: Параметры ядра: различия между версиями

Материал из Linux Wiki
Перейти к навигацииПерейти к поиску
(Новая: ; --showconfig: Показывает конфиг-файл, по которому было создано данное ядро iomem=<name>,<file> Configure <file> as an IO memory ...)
 
 
(не показана 1 промежуточная версия этого же участника)
Строка 1: Строка 1:
; --showconfig: Показывает конфиг-файл, по которому было создано данное ядро
; --showconfig:
    Показывает конфиг-файл, по которому было создано данное ядро


iomem=<name>,<file>
;iomem=<name>,<file>:
     Configure <file> as an IO memory region named <name>.
     Configure <file> as an IO memory region named <name>.


; mem=<Размер оперативной памяти>: Показывает, сколько физической оперативной памяти будет выделено виртуальной машине, может указываться через 'k', 'K', 'm', 'M'. Пример: '''mem=64M'''
; mem=<Размер оперативной памяти>:
    Показывает, сколько физической оперативной памяти будет выделено виртуальной машине, может указываться через 'k', 'K', 'm', 'M'. Пример: '''mem=64M'''


; --help:Вывести эту справку
; --help:Вывести эту справку
Строка 18: Строка 20:
         root=/dev/ubd5
         root=/dev/ubd5


;--version:Написать версию ядра
;--version:
    Написать версию ядра


;umid=<name>:
;umid=<name>:
Строка 136: Строка 139:
     The only flag currently supported is 'append', which specifies that all
     The only flag currently supported is 'append', which specifies that all
     files opened by hostfs will be opened in append mode.
     files opened by hostfs will be opened in append mode.
{{ToDo|Перевести}}


[[Category:User Mode Linux]]
[[Category:User Mode Linux]]

Текущая версия на 21:28, 13 ноября 2008

--showconfig
   Показывает конфиг-файл, по которому было создано данное ядро
iomem=<name>,<file>
   Configure <file> as an IO memory region named <name>.
mem=<Размер оперативной памяти>
   Показывает, сколько физической оперативной памяти будет выделено виртуальной машине, может указываться через 'k', 'K', 'm', 'M'. Пример: mem=64M
--help
Вывести эту справку
debug
   this flag is not needed to run gdb on UML in skas mode
root=<file containing the root fs>
   This is actually used by the generic kernel in exactly the same
   way as in any other kernel. If you configure a number of block
   devices and want to boot off something other than ubd0, you
   would use something like:
       root=/dev/ubd5
--version
   Написать версию ядра
umid=<name>
   This is used to assign a unique identity to this UML machine and
   is used for naming the pid file and management console socket.
con[0-9]*=<channel description>
   Attach a console or serial line to a host channel.  See
   http://user-mode-linux.sourceforge.net/old/input.html for a complete
   description of this switch.
ssl[0-9]*=<channel description>
   Attach a console or serial line to a host channel.  See
   http://user-mode-linux.sourceforge.net/old/input.html for a complete
   description of this switch.
eth[0-9]+=<transport>,<options>
   Configure a network device.
mconsole=notify
<socket>:
   Requests that the mconsole driver send a message to the named Unix
   socket containing the name of the mconsole socket.  This also serves
   to notify outside processes when UML has booted far enough to respond
   to mconsole requests.
udb
   This option is here solely to catch ubd -> udb typos, which can be
   to impossible to catch visually unless you specifically look for
   them.  The only result of any option starting with 'udb' is an error
   in the boot output.
ubd<n><flags>=<filename>[(
|,)<filename2>]:
   This is used to associate a device with a file in the underlying
   filesystem. When specifying two filenames, the first one is the
   COW name and the second is the backing file name. As separator you can
   use either a ':' or a ',': the first one allows writing things like;
       ubd0=~/Uml/root_cow:~/Uml/root_backing_file
   while with a ',' the shell would not expand the 2nd '~'.
   When using only one filename, UML will detect whether to treat it like
   a COW file or a backing file. To override this detection, add the 'd'
   flag:
       ubd0d=BackingFile
   Usually, there is a filesystem in the file, but
   that's not required. Swap devices containing swap files can be
   specified like this. Also, a file which doesn't contain a
   filesystem can have its contents read in the virtual
   machine by running 'dd' on the device. <n> must be in the range
   0 to 7. Appending an 'r' to the number will cause that device
   to be mounted read-only. For example ubd1r=./ext_fs. Appending
   an 's' will cause data to be written to disk on the host immediately.
   'c' will cause the device to be treated as being shared between multiple
   UMLs and file locking will be turned off - this is appropriate for a
   cluster filesystem and inappropriate at almost all other times.
fake_ide
   Create ide0 entries that map onto ubd devices.
xterm=<terminal emulator>,<title switch>,<exec switch>
   Specifies an alternate terminal emulator to use for the debugger,
   consoles, and serial lines when they are attached to the xterm channel.
   The values are the terminal emulator binary, the switch it uses to set
   its title, and the switch it uses to execute a subprocess,
   respectively.  The title switch must have the form '<switch> title',
   not '<switch>=title'.  Similarly, the exec switch must have the form
   '<switch> command arg1 arg2 ...'.
   The default values are 'xterm=xterm,-T,-e'.  Values for gnome-terminal
   are 'xterm=gnome-terminal,-t,-x'.
aio=2.4
   This is used to force UML to use 2.4-style AIO even when 2.6 AIO is
   available.  2.4 AIO is a single thread that handles one request at a
   time, synchronously.  2.6 AIO is a thread which uses the 2.6 AIO
   interface to handle an arbitrary number of pending requests.  2.6 AIO
   is not available in tt mode, on 2.4 hosts, or when UML is built with
   /usr/include/linux/aio_abi.h not available.  Many distributions don't
   include aio_abi.h, so you will need to copy it from a kernel tree to
   your /usr/include/linux in order to build an AIO-capable UML
noptraceldt
   Turns off usage of PTRACE_LDT, even if host supports it.
   To support PTRACE_LDT, the host needs to be patched using
   the current skas3 patch.
noptracefaultinfo
   Turns off usage of PTRACE_FAULTINFO, even if host supports
   it. To support PTRACE_FAULTINFO, the host needs to be patched
   using the current skas3 patch.
noprocmm
   Turns off usage of /proc/mm, even if host supports it.
   To support /proc/mm, the host needs to be patched using
   the current skas3 patch.
nosysemu
   Turns off syscall emulation patch for ptrace (SYSEMU) on.
   SYSEMU is a performance-patch introduced by Laurent Vivier. It changes
   behaviour of ptrace() and helps reducing host context switch rate.
   To make it working, you need a kernel patch for your host, too.
   See http://perso.wanadoo.fr/laurent.vivier/UML/ for further
   information.
mode=skas0
   Disables SKAS3 and SKAS4 usage, so that SKAS0 is used.
skas0
   Disables SKAS3 and SKAS4 usage, so that SKAS0 is used
uml_dir=<directory>
   The location to place the pid and umid files.
hostfs=<root dir>,<flags>,...
   This is used to set hostfs parameters.  The root directory argument
   is used to confine all hostfs mounts to within the specified directory
   tree on the host.  If this isn't specified, then a user inside UML can
   mount anything on the host that's accessible to the user that's running
   it.
   The only flag currently supported is 'append', which specifies that all
   files opened by hostfs will be opened in append mode.
ToDo: Перевести